« Angelo's Powerhouse Panasonic AM/FM 8-Track Player Radio | Main | Amazon Now Emailing Notifications That Your Customer Review Helped a Customer »

August 08, 2012



Details on automatic scans to find shortwave stations with the PL-390 vs. PL-660:

Side by side on my windowsill, the PL-390 scanned in up 21 good SW broadcast signals, although one of these was recorded as 5khz off its actual frequency. The PL-660 scanned in 32.

Each one scanned in one good station the other missed.

The PL-660 also scanned in as stations what seemed to be two spurious signals, 10 instances of electrical noise, and four "signals" which were actually spatter from strong signals the next frequency over; the PL-390 didn't log any of these.

What one radio could pick up the other could as well, as far as I could tell. Neither one was catching everything there was. I scanned the 49 meter band by hand and lost count of the number of stations; about 20 were coming in, I think. Any signal the 390 could hear, the 660 could also. The 660 had one that might have been a spurious signal. On the other hand, signals that were really too weak to make out sounded slightly less bad on the 660. It wasn't enough to make them listenable, but you could make out what was going on a little bit better.

I tried the sync to resolve some adjacent channel problems, and it works fine- if there is a strong interfering station on one side of the one you're trying to hear. Not if there are strong signals on both sides; in this case the sync made things worse.

All in all, an interesting mixed bag.


All PL660 that I know of have the 980 kHz spurious carrier. It seems to be produced by an internal DC/DC converter.
The worst feature of the PL660 is a sort of squelch that cuts the highs of low signals. It makes fading AM stations almost incomprehensible. This feature can be removed by modifying the radio. I did it with success. See youtube to find how.
Another "new" weakness is that the case of the tuning encoder is not connected to electrical ground; this makes tuning noisier sometimes. Again I corrected this easily.
I bought the PL660 to substitute my older PL600. After the above touchups (TECSUN !! read this) I can say that the PL660 is much better than the PL600 in every respect.
TECSUN, Please connect the microprocessor to the DC/DC converter and shift its frequency when the radio is tuned near 980 kHz and its harmonics. Thank you.


Thank you, Giorgio. It's good to know the problem with my 660 is not unique. It gives me some reassurance that the radio might not be about to die on me.

Strange that nobody mentioned this problem in the reviews I saw. I've seen too many product reviews that were matters of religion; true believers insisting The Product is perfect, worshipers of other brands saying it is a Crawling Abomination from Hell. It's almost as bad as operating system wars. I wish people would tell the truth in reviews, including the good and the bad. But if you did that, people looking to buy would be put off and tend to buy things about which the truth had NOT been told.

I was not able to find any instructions for modifying my PL-660 on the page you mentioned. It is in Russian and I don't read Russian. I used the Google translation but if there are any instructions in there they are nonsense to me. Of course I've never modified a radio, so it is likely I simply can't reconstruct what's being said. In any case, do you know of any idiot level instructions, including pictures, of what would need to be done?

Also, my sole electronics modification experience is soldering up custom RS-232 cables back in the day. This required some soldering in small spaces but nothing fancy. Is the modification required within such basic abilities?




Instructions for defeating the dynamic audio low pass filter of Tecsun PL660. (that I made on a rev.2 radio)

To illustrate the activity I link pictures and a video that are not mine. They are not under my control.
This picture shows the two tracks that must be shorted to disable the dynamic low pass filter (dynamic squelch):

To go there you need a good skill and be quite careless about any warranty, just think that you can do it:

0)A good solder station and a set of screwdrivers are required. Always pay great attention not to touch the plastic with the soldering iron.

1)Remove batteries, remove 4 screws on the back e and 2 screws in the battery compartment.
2)Pull out the 3 knobs.
3)Separate bottom and front shells. The electronics is now attached to the bottom shell. Do not touch LCD and the transparent window.
4)Look at the electronics. Look at the strap location. Write down the revision number of your radio that you can read on the PCB....
5)Remove the screw at the lower right corner as shown in the video.
6)Uplift the electronics, starting from the "knobs" side. Shift right and separate from the bottom shell.
7)On the back of the electronics there is the "big" shield. It has 4 solder points and 2 alignment small fin/slots. Remember where it is soldered. Remove the shield starting from the solder points that are far from the fin/slots.
8)Do the short by soldering a hair-thin copper wire taken from a common electrical bicycle wire.
9)Resolder the shield by first inserting the small fins in the slots.

time 0:16 "big" shield removed to access the two tracks that must be shorted.
time 0:35 shows the only screw that must be removed to uplift the PCB frame.

It is possible to convert the tone switch to a switch that enables and disables this modification.

Instead I kept the tone switch and defeated the dynamic filter in a permanent way with the thin wire.


Oops, keep track of the U shaped foot while "openig" this box. Maybe keep it in position with some tape.


Thanks! I'll look at this and see if I think it's something I could do. It doesn't sound too horrible.


This youtube video shows a strange non-fading carrier at 4820:
Because of the beat frequency of about 2kHz with a station, the strange carrier is not on channel.
The anomaly is not recognized as such.


In the above video a "chirping" carrier can be heard at 4800 kHz. The operator tries to cancel it with sync detection. By the sound, I can recognize this as a harmonics of the ~980 kHz spur.
I still don't know if all PL660 have this feature.
More comments are needed.
It is radiated by the radio circuitry and enters through the antenna. Because of that I believe that additional shielding of the supposed source DC/DC converter may solve the problem.

james patterson

The Harmonic Chirping,Squashy sound is exactly what I have in my radio,and when I put my hand on the antenna it certainly amplifies it.As mentioned in a reveiw by Giorgio.Im takeing my PL660 back,but it seems from most reviews,they all have this problem.Everdently the 600 doesnt have this problem,I havent read any.But according to other reveiws,the 600 has other problems.So can we DXers win at all?The Tecsun Receivers are said to be amongst the best in portables,then why all the problems?Im hopeing to check all the stock of PL660s where mine came from,there must be a good one amongst them,because I found no probs with FM,AM broadcast came in very well at my location.So if I can find one with no loud harmonics up on HF,well I'll be happy.Note that the harmonic sounds are alot worse if the SSB mode is set to on,and you wouldnt want that sound over top of a favourite frequency that you often listen to.I listen to 8.86700,Sth Pacific HF Airways.Well the harmonic sound is there and it climbs either up or down the band on its own.If you tune higher or lower,you will find it there somewhere.

Tom Welch

I would very much like to purchase a new world band radio, however, every month an international broadcaster goes out business. The latest is Radio Australia. I thinking a PL 390 now!!!

Meino Cramer

Recently I bought a PL-660 due to the sheer mass of postings I found about this receiver (massive bought items have better support often) and due to many good reviews.
I am amazed what this "little radio" is able to receive only with its internal antenna on shortwave. Tuning to 12065kHz I was able to catch ABC Australia while being at home in the evening ... ABC is more than 18000kmh away.

Mine has a serial, which can be interpreted as the radio was build 2015 (it contains these digits).

Mine has also this harmonics/birdie/spurious signal problem.
But -- at least for the harmonics in the shortwave bands: Its seems, that the "whatever is guilty for that birdie"-device tries to shift the carrier slowly out of the current dialed in frequency...at least with SSB activated the whistle become higher and weaker over a short period of time and than vanishes.
Since I still don't find any station broadcasting on the polluted frequencies I cannot state whether and how much the rest --if any remains-- disturbs the reception.
I read, that the DC-DC converter produces this annoying carrier...
On the other side: According to pictures of the internals of the PL-660 this part of the electronic is heavily shielded.
Due to the fact, that the noise becomes weaker if the antenna attenuator is set to local seems to indicate, that
the carrier does not pollute the power supply lines of the PCB but act as real "broadcaster" off the radio itself.
I can receive the carrier with another radio nearby.
Which in turn means: The carrier seems to be "shieldable".
I heard of PL-660ies. which do not have that problem. Which indicates that this is not a problem of PCB layout, design or software but one of manufacturing and calibration quality.
Or in other words: A professional may be able to fix this without Tecsuns intervention.
Unfortunately I neither have the knowledge nor the tools for that.
Anyone else? ;)


Well i received my PL-660 on 11 May 2018 and am satisfied with it so far. This is my 1st world band receiver. It is an impressive radio and been available since 2011 from what i read. I hope by this time Tecsun have fixed most problems with this model.

I researched many models before deciding on this particulour model. There are probably better models out there quality and function wise however I really liked the look of the PL-660, the ability to display frequency and time simultaneousley, the large lcd screen, auto scan, alarm and snooze functions.

I was and still am a bit concerned reading about so many PL-660s just dying, especially when connecting the external power supply. Mine came with a 120v supply which i cannot use as we are on 220v here.
Not too much of a problem though as i bought 2 sets of Duracell 2500 mAh cells that i rotate.

Overall I am happy with my PL-660 and it performs well, I just hope it does not die like so many others :(

Verify your Comment

Previewing your Comment

This is only a preview. Your comment has not yet been posted.

Your comment could not be posted. Error type:
Your comment has been posted. Post another comment

The letters and numbers you entered did not match the image. Please try again.

As a final step before posting your comment, enter the letters and numbers you see in the image below. This prevents automated programs from posting comments.

Having trouble reading this image? View an alternate.


Post a comment

Your Information

(Name and email address are required. Email address will not be displayed with the comment.)


  • Advertisements


  • Advertisements


  • Advertisements
My Photo


  • Advertisements


  • Advertisements


  • Advertisements

August 2020

Sun Mon Tue Wed Thu Fri Sat
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30 31          
Blog powered by Typepad


Companion Website: Breakthrough Writer

My Photo

Become a Fan